Multiplication machine

2013-06-03

This is definitely one of the nerdier projects I have pursued. A multiplication machine made from paper, powered by marbles running through the machine.

Here is it in action:

You can build one yourself, if are so inclined – you will find the template at the end of this post. Here it performs a 4×3 multiplication:

This is where you set the first factor, by adding the corresponding number of marbles:

P1270315

This is the reservoir, from which the marbles are moved to the output:

P1270317

And this is the core of the machine, the ‘adding unit’. By pulling out or pushing in the tabs, you can set the second factor:

P1270163-001

Admittedly, this project got a little bit out of hand. The idea is simple: Set the two factors of a multiplication, then let marbles run from a reservoir to the output until the result is reached. Making such a machine work, however, was surprisingly difficult. It took me several iterations and many fine-tunings to get to a paper-based machine that is robust enough to work reliably.

Before I go into the details on how to build the machine, here is a more detailed explanation of how it works and what happens during the multiplication:

Why a multiplication machine, you ask? Well, admittedly in an age where we are surrounded on all sides by computing power, there are easier ways to multiply. Especially in the range of 1 to 10, which we are talking about here. However, the machine turns multiplication into a physical process which is easy to observe. It essentially demonstrates how multiplication is a series of additions, thus making multiplication much more tangible for very young students.

And, being a physical machine, it can teach a lot about mechanics and (paper) engineering. Here are some interesting questions kids may ponder when using the machine:

  • What’s the trick? How does the multiplication work?
  • What are the limits of the machine? How small or large can the two factors be? Does 1 work? Does zero work?
  • What if something goes wrong? A marble gets stuck? There are not enough marbles in the reservoir? How does this affect the result?
  • Are there other uses for the machine? How could it be modified to work differently?

Now, how to build this beast? Well, first of all, this is not for the faint of heart. You will need about 20-40 hours, depending on your skill set. If you have a cutting plotter, things will be significantly easier, but it’s of course possible to do it with scissors and an x-acto knife. Also, as opposed to papercraft that has a purely aesthetic value, you will need to build this one very precisely, and likely several parts will require several build-test-refine cycles. If that doesn’t deter you, here is what you have to do:

Before you start, please note that the template is for marbles with a diameter of 14mm. If you don’t have these (and you will need as many as the highest product you want to calculate with the machine), I suggest that you scale the templates up or down to adjust to the size of the marbles you want to use. I don’t recomment deviating too much from 14mm though, as a widely different scale may break the mechanics, or at least need some adjustments.

First, print and cut out the 22 pages of the template, to be downloaded below. I used 190 gsm paper (about 53 lb “bond” ledger). Then, start with the frame (pages 1 to 8). The frame consists mostly of straight square beams. Each beam has five sides, four for the outside and one that serves as a glueing tab:

P1260981

It’s easiest to fold all four sides, then flatten the whole thing and glue it together. Afterwards, you can bring it back to its intended square shape:

P1260983

P1260984

 

Now it’s time to create two squares: Use two each of the ‘vertical corner struts’ and the horizontal ‘back and front struts’:

P1270347

This is how the corners connect:

P1260992

Now take the four ‘horizontal side struts’ and create the cube:

P1270349

P1270004

Ok, this is the frame which will carry the internals of the machine. Next, we need to add four more horizontal struts:

P1270008

P1270005

Now it’s time for four vertical struts, labeled ‘back center strut with hole for escapement’ and ‘front center strut with hole for escapement’. This is the first element that will connect to a moving part. In order to do so, the struts need holes in order to hold a toothpick that will later serve as an axle. Regular toothpicks are about 2mm in diameter. The holes, therefore, should be about 3mm in diameter. It is very important that the toothpick can rotate freely and with as little friction as possible.

P1270113

Here you can see where the struts go:

P1270114

Ok, finally two more horizontal struts which will later carry the adding unit. The adding unit must be mounted at a slope, so that the marbles can easily run downwards across it. Therefore, the struts are to be added at different heights:

P1270119

Alright, that wasn’t so difficult now, was it? Well, the next part admittedly will be a tad more difficult. The good news, though, is that it won’t get more complex than this. We need to build the adding unit. This is what we are aiming for:

P1270163

Before building it, I recommend watching this video which explains how it works:

This is a highly mechanical part with ten moving elements. It is very important that it is built as precisely as possible. Start with the frame:

P1270125

P1270127

Fold the large floor part back on itself, to create a slope. Then add the sides. Note that they, too, contain holes. However, this time we will not put a toothpick through the holes, but a larger skewer. The skewers I found are 3mm in diameter, so the holes are 4mm wide:

P1270129

Now add the back:

P1270133

P1270131

P1270132

P1270130

 

The next step is a lever bar which will reset the adding unit after a full cycle (more about this later). The bar runs across the whole adding unit and is held in place by a wooden skewer. At the right side, it has a basket which will catch the marbles coming out of the adding unit. This is what it looks like:

P1270140

P1270137

P1270139

Here are the parts:

P1270134

P1270135

Now we need to build nine so-called ‘rockers’. These are bistable elements that can be in an ‘up’ or ‘down’ position. As you will see later, the rockers are doing the counting during the multiplication – they keep track of how many marbles have passed the adding unit.

P1270148

These are the parts. The two small ones are the two sides of the rocker. Each contains a 4mm hole. The large one holds the two sides together. And the leftmost part will be a tab inside the rocker which can be pulled out or pushed in – more about that later.

Fold and glue the large part to one side. Pay attention to which side goes where – the rocker is asymmetrical. Also, there are two flat pieces that come together. Don’t glue them to each other.

P1270149

 

Now, build the tab. It should look like a distorted ‘T’:

P1270150

 

Put it inside the rocker, so that it can slide between the two flat pieces:

P1270154

Once the tab is in place, you can glue the other side to the rocker and finish it:

P1270153

As you can see, the rocker has an additional ‘wall’ on one side, to stop the incoming marbles. Also, there are small flaps at the side of one of the two flat pieces that hold the tab in place. Glue them together, so that the tab cannot fall out:

P1270151

P1270152

 

Good. Next we need spacers. Those are small, 1.6mm wide, strips of paper that are to form small circles or squares. I found it easiest to score them at four equidistant positions and fold them into squares. The diameter must be large enough to allow the spacers to go onto the skewer without friction.

P1270146

P1270147

Time to assemble the adding unit:

P1270158

Thread the skewer through the right side of the frame, then add a spacer, then a rocker, again a spacer, and so on.

P1270161

 

The unit should finally contain nine rockers, each separated by a spacer from the next. Note that there should also be a spacer before the first and after the last rocker. Now add the lever bar by threading it onto the skewer.

Congratulations – the most difficult part is over. Now on to the two so-called ‘escapements’. The idea behind them is that they release one marble at a time, each release being triggered by another marble passing below. There are two of them, each feeding into the adding unit from different sides.

P1270164

They consist of a conduit with a hole in the middle, and a shaft that fits into the hole:

 

P1270167

The straight escapement goes to the front of the machine, and the curved one to the back:

P1270183

 

Note the square spacer that connects the shaft of the escapement to the vertical struts and holds it securely in place.

Next, build balances that form the bottom part of the escapement. These contain 3mm holes as well as square holes. For the latter, you will need a sharp xacto or similar crafting knife:

P1270121

P1270122

P1270123

The escapement balances are attached to the frame using toothpicks, like so:

P1270246

 

The second toothpick holds a piston in place that goes through the shaft at the top. In this way, a marble resting in the hole over the piston will be released from the escapement when another marble falls onto the balance:

Ok, we now have to do some plumbing, connecting the various parts. The pieces you will need are found on template pages 16-18. Start with a straight piece connecting to the curved escapement in the back, then to a short chute. The chute connects to another straight conduit leading to the left side:

P1270194

P1270191

P1270193

P1270192

A 180°C turn connects the conduit to the left side of the adding unit, which can be placed on the skewed horizontal struts:

P1270197

 

The front escapement connects to a 90°C curve and then a straight conduit leading to the chute:

P1270204

P1270202

 

Now we need to connect the output side of the adding unit to the escapements. There are two outputs: One is at the back of the unit, the other is the basket. The one for the basket goes to the front and looks like this:

P1270216

You will find the parts on page 17. The other one is for the back and can be found on page 18. It looks like this:

P1270205

Glue them in place like so:

P1270212

P1270210

Next, we need to set up walls around the escapements, so that incoming marbles don’t go stray.

P1270243

P1270244

 

This is how they should look:

P1270246

P1270245

Now we are almost there. In fact, you can already start testing the machine (if you haven’t done so already anyway). In order to complete it, you need to add more capacity for stored marbles at the top, the so-called reservoir. Frankly, this gave me some headache, because it’s not easy to store several dozen of marbles and release them in a controlled way. Their weight is enough to make the escapement slip and release more than one marble at a time. In order to mitigate the weight, I have constructed four balances that each hold about a dozen marbles. It looks like this:

P1270351

P1270353

P1270354

And here is a video on how it operates:

The first balance blocks the others. Only when it is emptied, it will tilt and the marbles from the next one will become available. In this way, the maximum load on the escapement is a dozen marbles (plus a few in the conduit from the reservoir balances to the escapement).

Here is how to build the reservoir: First, build for each balance the following cage:

P1270251

Next, the actual balance:

P1270252

P1270253

 

Add this wall:

P1270254

And a wall on the other side, as well as a small coin as a weight:

P1270256

 

Now, glue the top cover on page 19 to the top of the machine. Connect the back escapement to the channel that leads from the reservoir to the escapement.

P1270356

Glue the block of reservoir balances onto the top cover, so that the balance exits align with the channel.

Ok, we need just one final thing: An outlet that collects and funnels the marbles the machine outputs. This is on page 22 of the template. Simply glue it to the right vertical struts of the machine, like so:

P1270360

P1270357

P1270358

Congratulations, you are done! Now it’s time for some testing and finetuning. Check that all moving parts work well with as little friction as possible. Make sure that the marbles can traverse the conduits without blockage. If you come across any problems you cannot debug, please post a comment and I will try to help.

Here is the template in PDF format.

Creative Commons LicenseThis work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. For more details on what you can and cannot do with my work, see here.

Comments

  1. Mike McNall,

    Markus,

    Finally, 4 years after first seeing it, I am building the multiplication machine. I am doing pretty well, but I have some questions I hope you can answer:

    1. I don’t know how to finish the front of the adding unit frame-the part with the 4 or 5 long horizontal lines. I can’t tell from the photos what it looks like or how to complete it.

    2. The escapement reservoir 2
    a. Do I glue the little triangles inside the tube or on the outside/bottom?
    b. Where exactly does this escapement go? I can’t see from the pictures. I think it’s on the opposite side from the straight escapement. Can you show a picture or explain its placement?

    Thanks very much.

    1. admin,

      Hi Mike, first of all, congratulations for taking on this project! I didn’t expect anybody to really try it – in fact, I realized after it was done that I went a bit overboard with it.

      Anyway, concerning your questions:
      1. You mean the four thin, connected strips on page 9? They fold inward in order to form a square bar at the top of the adding unit. In this picture, you can see them not yet folded:

      In this picture, you can see the finished bar:

      2a. They should go on the outside/bottom, so that they don’t interfere with the marbles rolling down.

      2b. Yes, it is pretty much at the opposite side from the other escapement. You can see it best in this video. I realize that the pictures shown do not give a good overall overview of the construction. Unfortunately, the original machine does no longer exist, so I can’t quickly take new photos. Hope the video helps, but if not, please let me know, and I will try to elaborate more.

    2. Mike McNall,

      Markus,

      I am still laughing over the fact you didn’t expect anyone to build the X machine! I am building it for my son-in-law as a Christmas gift. He is nearly a math genius and loves machines like this. I’m also giving him the printed directions along with the templates because I know he likes to do things himself. Perhaps if he makes his own machine he’ll give this one back to me!

      I have taken care of question 1 and 2a thanks to you. I will have to examine the video and pictures more carefully to answer 2b. Thanks for your offer to ask more questions. I won’t hesitate to ask them.

      Danke.

      Mike

      1. Mike McNall,

        Hi Markus,

        Well, the multiplication machine is completed! However, it will take a lot of finessing to get it to run smoothly like yours. Right now I am trying to adjust the height and tilt of the adding unit. It is a fun process.

        My friends and I are having a little artisan and craft fair at a local barber shop in 3 weeks. I was thinking of making a mobile out of your alphabet animals if I have your permission to make one set to sell. I will be happy to pay whatever royalty you ask.

        Thanks ,

        Mike

        1. admin,

          Contragulations on finishing the machine! It took me a while, too, to adjust it so that it would work smoothly.

          As for the fair, I sent you an email.

  2. rakesh,

    This is a treasure trove for children. Thanks for sharing this creative works of yours!

  3. Norbert,

    Hallo Markus,

    ich entschuldige mich, falls ich falsch liege, aber Markus hört sich ziemlich deutsch an.
    Ich möchte die Multiplikations Maschine bauen aber habe doch kleine Probleme.
    Gibt es auch eine Anleitung in deutscher Sprache, da ich der englischen nicht mehr
    so mächtig bin?

    Liebe Grüße
    Norbert

  4. jet,

    LOL awesome,and brilliant . i will sure give it a try.
    thank you for the tute and sharing.!

  5. teaha .h,

    simply WOW..will definitely try this one! thanks for sharing :)

    1. admin,

      Thanks for the kind comment! If you do indeed try this, be advised that it is quite tricky to get it working perfectly. Some patience is definitely required.

  6. admin,

    Sebastian noticed a mistake on page 4 of the template: The grey areas which indicate where the ‘horizontal inner struts’ attach to the ‘horizontal side struts’ were shifted to the wrong place.

    I have corrected the mistake and re-uploaded the template. Sorry, and many thanks to Sebastian!

  7. admin,

    Cagri from Istanbul kindly pointed out that the crease lines were missing from page 11 of the template. I have fixed that.

    Also, on a related note. Cagri asked about the number of rockers: There are five in the template on page 12, but in the video there are more.

    That’s correct – you can add more than five, and in fact if you want to be able to multiply up to 100, you have to have eight (each holding 12 marbles, plus a couple in the conduit leading to the escapement). So, simply print page 12 two times and assemble eight of the ten.

Comments are closed.

-->